/*
* The MySensors Arduino library handles the wireless radio link and protocol
* between your home built sensors/actuators and HA controller of choice.
* The sensors forms a self healing radio network with optional repeaters. Each
* repeater and gateway builds a routing tables in EEPROM which keeps track of the
* network topology allowing messages to be routed to nodes.
*
* Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
* Copyright (C) 2013-2019 Sensnology AB
* Full contributor list: https://github.com/mysensors/MySensors/graphs/contributors
*
* Documentation: http://www.mysensors.org
* Support Forum: http://forum.mysensors.org
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation.
*/
#include <iostream>
#include <cstdio>
#include <unistd.h>
// For more options run ./configure --help
// Config file
//#define MY_LINUX_CONFIG_FILE "/etc/mysensors.conf"
// How many clients should be able to connect to this gateway (default 1)
#define MY_GATEWAY_MAX_CLIENTS 10
// Serial config
// Enable this if you are using an Arduino connected to the USB
//#define MY_LINUX_SERIAL_PORT "/dev/ttyUSB0"
// Enable this if you need to connect to a controller running on the same device
// You also need to define MY_LINUX_SERIAL_PORT above with the symlink name for the PTY device
//#define MY_LINUX_SERIAL_IS_PTY
// Grant access to the specified system group for the serial device
//#define MY_LINUX_SERIAL_GROUPNAME "tty"
// MQTT options
//#define MY_CONTROLLER_IP_ADDRESS 192, 168, 178, 68
//#define MY_PORT 1883
//#define MY_MQTT_CLIENT_ID "mysensors-1"
//#define MY_MQTT_PUBLISH_TOPIC_PREFIX "mygateway1-out"
//#define MY_MQTT_SUBSCRIBE_TOPIC_PREFIX "mygateway1-in"
// Enable these if your MQTT broker requires username/password
//#define MY_MQTT_USER "username"
//#define MY_MQTT_PASSWORD "password"
// Flash leds on rx/tx/err
//#define MY_DEFAULT_ERR_LED_PIN 12 // Error LED pin
//#define MY_DEFAULT_RX_LED_PIN 16 // Receive LED pin
//#define MY_DEFAULT_TX_LED_PIN 18 // Transmit LED pin
// Inverse the blinking feature
//#define MY_WITH_LEDS_BLINKING_INVERSE
// Enable software signing
//#define MY_SIGNING_SOFT
// Enable signing related debug
//#define MY_DEBUG_VERBOSE_SIGNING
// Enable this to request signatures
//#define MY_SIGNING_REQUEST_SIGNATURES
// Enable this to to weaken security for gradual deployment purpose
// (see signing documentation for details)
//#define MY_SIGNING_WEAK_SECURITY
// Enables RF24 encryption (all nodes and gateway must have this enabled, and all must be
// personalized with the same AES key)
//#define MY_RF24_ENABLE_ENCRYPTION
// Enable inclusion mode if your HA Controller supports it (e.g. Vera Controller)
//#define MY_INCLUSION_MODE_FEATURE
// Enable Inclusion mode button on gateway
//#define MY_INCLUSION_BUTTON_FEATURE
// Set inclusion mode duration (in seconds)
//#define MY_INCLUSION_MODE_DURATION 60
// Digital pin used for inclusion mode button
//#define MY_INCLUSION_MODE_BUTTON_PIN 3
#include <MySensors.h>
#define ARDUINO 100
// This space is intended to be used to include arduino libraries
#undef ARDUINO
void setup()
{
// Setup locally attached sensors
}
void presentation()
{
// Present locally attached sensors here
}
void loop()
{
// Send locally attached sensors data here
}