codes.crepp.org

/*
 * The MySensors Arduino library handles the wireless radio link and protocol
 * between your home built sensors/actuators and HA controller of choice.
 * The sensors forms a self healing radio network with optional repeaters. Each
 * repeater and gateway builds a routing tables in EEPROM which keeps track of the
 * network topology allowing messages to be routed to nodes.
 *
 * Created by Henrik Ekblad <henrik.ekblad@mysensors.org>
 * Copyright (C) 2013-2019 Sensnology AB
 * Full contributor list: https://github.com/mysensors/MySensors/graphs/contributors
 *
 * Documentation: http://www.mysensors.org
 * Support Forum: http://forum.mysensors.org
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License
 * version 2 as published by the Free Software Foundation.
 *
 *******************************
 *
 *  This is a simple sketch used to demonstrate and test node-to-node MySensors communication.
 *  To use this sketch, assemble MySensors nodes - they need nothing more than a radio
 *  1.  Flash each node with the same sketch, open the console and type either 0 or 1 to the respective nodes to set their ID
 *  2.  You only need to set the node id once, and restart the nodes
 *  3.  To being a ping-pong test, simply type T in the console for one of the nodes.
 *
 *  2015-05-25 Bruce Lacey v1.0
 */

// Enable debug prints to serial monitor
#define MY_DEBUG

// Enable and select radio type attached
#define MY_RADIO_RF24
//#define MY_RADIO_NRF5_ESB
//#define MY_RADIO_RFM69
//#define MY_RADIO_RFM95

#include <MySensors.h>
#include "MYSLog.h"

#define VSN "v1.0"

// Define two generic nodes with a single child
#define YING 200
#define YANG 201
#define CHILD 1

MyMessage mPing(CHILD, V_VAR1);   //Ping message
MyMessage mPong(CHILD, V_VAR2);   //Pong message

void setup()
{
}

void presentation()
{
	present(CHILD, S_CUSTOM);  //

	sendSketchInfo( nodeTypeAsCharRepresentation( getNodeId() ), VSN );
	LOG(F("\n%sReady.\n"), nodeTypeAsCharRepresentation(getNodeId()));
}

void loop()
{

	// Interactive command and control
	// Entering a number from 0 or 1 will write the node 200 (YING) or 201 (YANG) to EEPROM
	// Entering T on either node will initiate a ping-pong test.
	if (Serial.available()) {
		byte inChar = Serial.read();
		uint8_t node = getNodeId();

		// Manual Test Mode
		if (inChar == 'T' || inChar == 't') {
			LOG(F("T received - starting test...\n"));
			MyMessage msg = mPong;
			msg.sender = (node == YING ? YANG : YING);
			sendPingOrPongResponse( msg );
		} else if (inChar == '0' or inChar == '1') {
			byte nodeID = 200 + (inChar - '0');
			setNodeId(nodeID);
		} else {
			LOG("Invalid input\n");
		}
	}
}

void receive(const MyMessage &message)
{

	LOG(F("Received %s from %s\n"), msgTypeAsCharRepresentation((mysensors_data_t)message.getType()),
	    nodeTypeAsCharRepresentation(message.sender));

	delay(250);
	sendPingOrPongResponse( message );
}

void sendPingOrPongResponse( MyMessage msg )
{

	MyMessage response = (msg.getType() == V_VAR1 ? mPong : mPing);

	LOG(F("Sending %s to %s\n"), msgTypeAsCharRepresentation( (mysensors_data_t)response.getType() ),
	    nodeTypeAsCharRepresentation(msg.sender));

	// Set payload to current time in millis to ensure each message is unique
	response.set( (uint32_t)millis() );
	response.setDestination(msg.sender);
	send(response);
}

void setNodeId(byte nodeID)
{
	LOG(F("Setting node id to: %i.\n***Please restart the node for changes to take effect.\n"), nodeID);
	hwWriteConfig(EEPROM_NODE_ID_ADDRESS, (byte)nodeID);
}

const char * msgTypeAsCharRepresentation( mysensors_data_t mType )
{
	return mType == V_VAR1 ? "Ping" : "Pong";
}

const char * nodeTypeAsCharRepresentation( uint8_t node )
{
	return node == YING ? "Ying Node" : "Yang Node";
}